Zoiper android login failed1/16/2024 To unsubscribe from these emails, click here. Last Modified: 15:55:28 Bad Audio Quality Introduction: This tutorial is about bad quality audio. you probably need 'Authentication user', which is in most cases the same. Configuring, disabling and enabling STUN: Zoiper Classic. Default STUN values: Server hostname /IP : Port : 3478 UDP/TCP Refresh period : 30. SIP 401 means that you are not 'authorized', e.g. All Zoiper products support our backup STUN server (), however if your VoIP provider is running their own STUN server, use it instead. The 'null' is not related to the SIP 401. You can just go add 'account name' and everything will be fine. How many Zoiper users can be connected at the same time? Ted, KC3OL. Errors & Problems Error 408 Request Timeout This error means that the phone did not receive a reply from the server (or there is no connectivity with it) and is common with new installation. Displaying the account name as 'null' is a bug in Zoiper and it is going to be fixed. I am running Allstar on a Raspberry Pi 3B+. Visit Topic or reply to this email to respond. How many Zoiper users are you expecting? BTW, the same ID/password can be used for all Zoiper users if you like. One of them is at the same local network of FreePBX server and has IP Address (192.168.1.58). I would think a dozen or two should be fine but I never tested it. pjsip set logger on Extension 881 has two endpoints. Keep an eye on your CPU, watch the bandwidth and if things start going to heck you’ve reached the limit for your setup. I have also used the IP address for the server just in case there was a DNS problem. That’s hard to say exactly because it depends on many factors. How many Zoiper users can be connected at the same time? On Jul 22, 2019, at 4:05 PM, Tim Sawyer via AllStarLink Discussion Groups wrote: That is not CID info, but an actual login attempt with that extension name. Since then I have made changes to iax.conf and extensions per your recommendations and am hoping that all will be OK. Well something isn’t right there, as the error is telling you that something is trying to login with a username of Name, and the password it’s providing is not valid. There were three of us connected at the time when this happened. When I first set it up earlier today with the PTT option today someone got stuck in the XMIT mode and tapping on the # did not work. I estimate 5-6 users at the same time so there shouldn’t be a problem. The best way to learn about asterisk is the definitive book on Asterisk, the O’reilly book.īut there are lots of places on the net with most all of what is in that book. All of the users created in iax.conf will use this same configuration. In /etc/asterisk/custom/nf add the following lines. Start Zoiper for Android, click 'Config', select 'Accounts' and then 'Add account. Repeat these lines for each user, replacing with the users call sign and replace with call sign in caps ie callerid=“WB6XXX”. If you want to have individual IDs, use the configuration below in place of or in addition to the configuration above. Any number of users can use this ID at the same time. This sets the user ID to zoiper and password to the password of your choice. NOTICE: Information provided in our FAQ section is provided only for convenience, and does not constitute legal advice. In /etc/asterisk/custom/iax.conf add the following lines. The Zoiper configuration below allows connections to any node on your AllStar server. check Zoiper 'Config'-'Connectivity' and make sure 'Run in background' and 'Keep Alive WiFi' are enabled. Displays Network statistics of active call.Zoiper is an iOS and Android VoIP telephone app that can be used with AllStar.Click to save number to clipboard to easily paste/save.Click and select what label to assign to the active call.More Than one active call is required, can receive and make additional calls to conference. Start a Conference between 2 or more active calls.Click to add current active call to contacts.Click on Parking Lot to open contextual menu and furhter direct a call or retreive it. Transfer a call, once selected input destination and select Attended (Speak to Recipient of call first) or Blind (Instant) Transfer.Toggle call recording, will show flashing red if call is being recorded.This can be achieved by clicking or typing the keys 0 - 9, # or * Shows dialpad to make use of DTMF (Dual Tone – Multi Frequency) for option selection or entering details on a call.Figure 3.7 Softphone Application - Active Call.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |